1064/3 MSV Series Diaphragm Pilot Solenoid Valve
|Payment Type:||L/C,T/T,Paypal,Money Gram,Western Union|
|Terms of Trade:||FOB,CFR,CIF,EXW|
|Min. Order:||1 Piece/Pieces|
|Delivery Time:||About 8 Days|
|Productivity:||1120 sets/ 1 week|
|Place of Origin:||NINGBO CHINA|
|Supply Ability:||4550 /set per month|
Model No.: MSV-1064/3
1064/3 MSV Series Diaphragm Pilot Solenoid Valve
After purchasing the MSV refrigeration solenoid valves, you need to know the color of the wires in the cable. The yellow/green wire is always the ground wire. The wire for each color is not a phase line but a neutral line. Make sure the coil data (voltage and frequency) corresponds to the supply voltage. If it does not correspond, the coil may be burnt. Always ensure that the valve matches the coil. For systems where the valve must remain closed (not energized) during most of the operating time, an NC solenoid valve should be used. For systems where the valve must remain open (not energized) during most of the operating time, a NO solenoid valve should be used. The NO solenoid valve cannot be replaced with an NC solenoid valve.
Technical information of 1064/3 MSV Flare Refrigeration Solenoid Valve:
Model No. Castel type MSV-1064/3 series Connection G 3/8'' Inch SAE Refrigerant R407C, R410A, R22, R134a Media temperature -40℃-105℃ Max. opening pressure 25 Bar Min. opening pressure 0.5 Bar Working pressure 30 bar KV values 0.8 m³/h Height 82 mm Length 68 mm
Compressor units working processing with MSV-1064/3 3/8'' Refrigerator Solenoid Valve:
Producing view of Castel type MSV-1064/3 chiller solenoid valve for R407c, R410a, R22,R134a medium:
Carton and pallet packing view of MSV type 1064/3 electric solenoid valve For Refrigeration Suction Line,Flare:
Fresh-keeping cabinet with 1064/3 MSV Series Diaphragm Pilot Solenoid Valve?
The structure of the rolling compressor of the fresh-keeping cabinet is mainly composed of a motor, a rolling piston, an eccentric shaft, a sliding piece, a spring, an air suction hole, an exhaust valve piece, etc. (no suction valve piece).
The slider of the fresh-keeping cabinet is equal in height to the cylindrical rotor, the cylinder height is slightly higher than the rotor, the cylinder head is covered with a cylinder head, and there is a certain gap between the piston end surface and the cylinder head plane, so that the piston and the slider can be freely in the cylinder. Movement, there are suction and exhaust holes on the cylinder block on both sides of the cylinder groove, the suction hole has no suction valve, and the refrigerant vapor directly enters the suction hole of the cylinder from the steam pipe. In order to prevent liquid blow, a gas-liquid separator is arranged on the suction pipe; an exhaust valve is arranged on the exhaust port, and the gas in the cylinder is discharged into the casing, so that the inside of the casing is a high-pressure gas zone, and then the high-pressure gas is further composed of a shell. The body enters the exhaust passage.
Fruit storage cabinet
The fresh-keeping cabinet rolling piston compressor is generally a vertical structure. The compressor is installed in the lower part of the fresh-keeping cabinet. The motor is in the upper part. The outer part of the whole cylinder is almost immersed in the lubricating oil. The cylindrical piston is installed in the cylinder and is placed on the eccentric shaft. Eccentric turn, eccentric axis. For the shaft to drive the piston in the cylinder along the cylinder wall surface of the cylinder wall has a through slot, the slot is equipped with a slider, the slider and the rotor fit in the slot sliding, under the action of the spring force and the rolling rotor outer wall surface The dynamic seal is formed by contact, and the crescent-shaped space between the rolling rotor and the cylinder wall is divided into a helium chamber and a compression chamber. During the process of rotating the eccentric shaft around the center of the cylinder, the helium chamber completes the intake process, and the compression chamber completes the compression. And the exhaust process.
Welcome to your inquiry!
NINGBO BRANDO HARDWARE CO.,LTD
BRANDO is one of leading manufacturers of solenoids, armature assembly, and solenoid valve in China, located in China main sea port city -- NINGBO, the location with high convenience of shipment not only by air but also by ocean.
BRANDO has 4800 square meter workshops and around 50 employees, developed about 10 years from year 2008 by focusing on products quality, design, service, now with good reputation from all over the world and our annual output value increasing yearly by yearly, moreover, more than 90% of annual output value is from exporting brought from our high quality and best customer service. We highly believe to run the company and brand well should keep faith of BEST QUALITY, BEST ATTITUDE, and BEST CUSTOMER SERVICE.
BRANDO`s products range covering solenoid coil, solenoid valve armature assembly, various solenoid valves, fluid medium such like pneumatic, hydraulic, water, hot water, air, steam, gas, oil, chemical liquid and Others. We supply OEM and ODM, all products widely applications for automotive, automation, textile industry, pneumatic , hydraulic, air and water treatment systems and so on.
Model series have such like Q22HD, 2W, 2S, US, 2L, 223, 6014, 0311, 0927, 0955, PU220, PU225, 2P, 2V, VX2120, QX, VX22, VX31/32/33, ZQDF, SCG, CA, DMF, 4V100, 4V200, 4V300, 4V400, VF, VZ, EVR, etc... Any request just feel free to contact our sales team, will response once get message, email or calling.
BRANDO company is approved by ISO9001:2008 system and managed by 5S management, with clean workshop environment and high precision machines and strict operation paperwork procedure to ensure the production well, save delivery time, and reduce any waste to satisfy all clients all over the world.
BRANDO company welcome clients from all over the world, we attend exhibition in many countries, such like America, Europe, Australia, Malaysia, Pakistan, Egypt, New Zealand, Poland, Germany, Korea, India, Indonesia, etc. We highly welcome your visit at our booth or our company.
Quick review of BRANDO products:
- Company Name: NINGBO BRANDO HARDWARE CO.,LTD
- Representative: Lu Jin Jun
- Product/Service: Solenoid Valve Armatures , Solenoid Valve Coils , Pneumatic Solenoid Valves , Pneumatic Cylinders , Pulse Jet Diaphragm Valves , Pneumatic Components
- Capital (Million US $): 1000,000RMB
- Year Established: 2008
- Total Annual Sales Volume (Million US $): US$5 Million - US$10 Million
- Export Percentage: 81% - 90%
- Total Annual Purchase Volume (Million US $): US$1 Million - US$2.5 Million
- No. of Production Lines: 10
- No. of R&D Staff: 5 -10 People
- No. of QC Staff: 11 -20 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): 3,000-5,000 square meters
- Factory Location: Ningbo
- Contact Person: Mr. Brandon Bao
- Tel: 86-0574-83879820
Premium Related Products